How to hook up a dryer – BuzzTMZ How to hook up a dryer – BuzzTMZ

How to hook up gas dryer vent, you have successfully subscribed! thanks from the hometips team.

Step 4 — Cut a Hole Outside, cut a larger hole where the vent will be coming through using a hole saw. The fourth step is to check the vent hole in the gas dryer to ensure it matches the vent hole of the home.

o bar leicester speed dating

Then hook up the vent pipe you ran to that elbow. Be sure the vent exhausts to the outdoors. Once the pipes are in place, wrap the joints with metal tape to seal them.

boys meet girls trailer trash

A gas provider can answer questions about the installation kit. Step 5 — Attach the Vent Hood Install the vent hood to the side of the house using wood screws and then caulk around the shroud and pipe the vent hood should have a 12 inch piece of pipe pre-attached to it.

However, it is a necessity, because it keeps possibly unsafe gases and fibers from entering your house. If the dryer vent and the outside vent are directly above and below each other, solid metal pipe is preferred with two degree angles.

But you can also undertake installation yourself. Shut the power off at the breaker box before doing any new installations. How to Install a Clothes Dryer April 27, Instructions for installing a gas dryer, including connecting to the gas line and to venting When you buy a new dryer, you can usually pay coy smile flirting small fee to have it delivered and hooked up.

How to Hook Up a Gas Dryer ru-tubbe.ru

The second step is to install the gas connection for a gas dryer. If bubbles appear, there is a leak. You can determine where the spot is by measuring from the corner of the foundation or even a window inside and then going outside and using the same marker to relocate the spot.

The metal vent pipe on the back of the dryer is inserted into the flexible pipe and the end of the flexible pipe is inserted into the exhaust hole vent.

Push the dryer into place, leaving a couple of inches on each side for air circulation. Tighten them down firmly.

Wie Daten Ihre Werbeerlebnisse verbessern

The sixth step is to put the pipe dope on the threads and take the stainless steel connector and screw it to the pipe. You can use rigid sheet metal pipe to avoid sagging.

The job is quite simple if the laundry area is already set up for the machine. If the gas supply is installed with the wrong size shutoff valve, use the pipe wrench to hold the pipe, so it doesn't turn while the shutoff valve is removed.

The ninth step is to plug the gas dryer in and attach the loose end of the vent hose. The vent pieces leading away from the dryer are considered the "male" pieces. Plug the power cord into a matching receptacle. For example, the vent pipe on the back of the dryer is inserted into the next piece of pipe; that piece of pipe is inserted into a degree bend upward, and then the degree end of the pipe is inserted into the following pipe as it rises toward the exhaust vent.

Add Your Answer

The third step is to shut off the electrical power. Most dryers discharge this air through an outside vent that is connected with a hose. Tighten the connections and test again. Connect a 4-inch-diameter metal duct from the dryer to the vent wall flange.

If necessary, turn the adjustable feet at the front of the unit to properly level it. Using hose clamps, fasten a degree elbow to the end of the vent pipe that is already in place.

How to Hook Up the Metal Vent From the Back of the Dryer | Home Guides | SF Gate

Follow the instructions in the dryer installation kit. The tenth step is to turn the gas and breaker box back on.

que es orfebre yahoo dating

Keep the dryer at least 3 inches away from the wall for circulation. A gas dryer will have a conventional plug.

Bevor Sie fortfahren...

Keep the vent hose to the shortest length possible to increase drying time and the efficiency of the dryer. Properly installing the vent hose is the key to hooking up the metal vent on the back of a dryer. Call for free estimates from local appliance pros now: These pieces are always inserted inside the pipe during the run.

Mix 50 percent water with 50 percent liquid dish soap and put the solution on the newly installed gas connections, then turn the gas on. To seal the joints connecting the pipe segments, use foil tape.

Can you use copper gas line to hook up a gas dryer

A gas dryer involves connecting both a gas supply line and a vent to the appliance. Cut the pipe to the length needed with a tin snips while wearing gloves. Do not insert screws, because the threads will collect lint and begin to clog the pipe.

The seventh step is to check for leaks once the dryer's gas line is hooked up. Step-by-Step Dryer Installation 1To hook up a gas dryer, turn the gas off at the shutoff valve.

Wash the floor where the gas dryer is to sit and let it dry. The guide hole you cut earlier should be in the very center of the large 4 inch hole.

If it doesn't, a new dryer vent hole needs to be cut. Step 3 — Drill Drill a small guide hole inside the house where the dryer vent will be.

Gas dryer vent piping replaced complete vidos.cc

Secure the ends with band clamps of the correct size. The fifth step is to clean up the surrounding area. Step 1 — Choose Your Pipe Flexible plastic hose is very commonly used in homes but it tends to sag.

The dryer tumbles, a heating element or a gas burner ignites and this hot air is swirled around your clothing and discharged from the vent at the rear of the dryer. Step 2 — Location Decide where you want your dryer vent to be located.

If the vents are in different locations, a flexible metal pipe works best. Wrap the threads of the gas supply pipe with pipe-wrap tape use the type made for gas connectionsand then tighten a stainless-steel connector onto the pipe.